材料

FAMU-FSU scientists identify ideal parameters for 3D printing conductive graphite composites

Researchers from theFAMU-FSU College of Engineeringhave developed a parameter set for 3D printing graphene-based structures with optimized conductive qualities.

After a series of test runs, the team found that while factors like print pressure and nozzle diameter affected the composite’s properties, at specific speeds, its particles could be aligned vertically. Using these parameters as a guide, the scientists produced a material with enhanced strength and conductivity, potentially making it ideal for use within military applications such as 3D printing heat sinks or shielding.

“We found that a wide-range of matrix filler combinations allow for versatility in the properties of the printed material,” said lead author Professor Subramanian Ramakrishnan. “By fine tuning the way they are processed, we can suggest guidelines that maximize the effectiveness and performance of the composites.”

Professor S. Ramakrishnan and student Roneisha Haney (pictured) believe their approach could yield a new generation of composites. Photo via FAMU-FSU.

Conductive matrix-filler composites

Composites are so widely-used within 3D printing, and there are so many matrix-filler combinations available, that users can often tailor them to meet the specific needs of their application. Likewise, graphene nanoplatelets (GNPs) are potentially well-suited to this role, due to their optimal thermal and electrical properties, and ideal aspect ratio for the job.

Epoxy resins, meanwhile, are known for their flexibility and ease of processing, which could make them perfect for combining with GNPs to form thermal interface materials. However, the properties of such composites would depend on factors such as the rheology of the inks used to create them and their concentration, areas that aren’t yet fully understood.

Previous studies have shown that using Direct Ink Writing (DIW) to 3D print GNP-loaded materials, induces a shear force on their filler, causing their particles to align with the orientation of the print. How exactly this occurs and its impact on conductivity remains somewhat of a mystery, hence the team sought to quantify the exact mechanics of the process.

“Our aim is to 3D print lightweight conductive composites and to study the effect of printing conditions on particle orientation and final composite performance,” explained Ramakrishnan. “The combination of epoxy resins and graphene nano-platelets is of interest in several applications for theU.S. Air Force.”

The researchers 3D printed a cone-shape utilizing their graphene-based composite (pictured) to use as a mask in their fluids lab. Photo via FAMU-FSU.

Identifying the optimized set-up

In order to fabricate optimal graphene structures, the team developed a novel ink, in which they included concentrations of GNPs that varied from 7% up to 18%. The custom material was then loaded into annScrypt 3Dn-300system, and deposited using different speeds and pressures to generate the widest possible dataset.

Once the composites had been printed and cured into specimens, their electrical resistance was measured using X-ray and microscopy processes. Interestingly, results showed that the inks with GNP levels higher than 13% exhibited increased shear thinning, yielding samples with enhanced strength and conductivity.

Similarly, the scientists found that increasing the print speed from 5 mm/s to 40mm/s caused more shear, and led the material’s particles to converge in the print’s direction. In fact, the effect was so profound, that compared to GNP-infused injection molded parts, the team’s samples were up to 619 s/cm more conductive.

Overall, the researchers believe that their parameter set represents a cost-effective method of controlling particle orientation that could yield novel polymeric nanocomposites. What’s more, given thatU.S. Air Force Research Laboratoryscientists contributed to the study, the materials could also find end-use military applications such as corrosion-resistant coatings or even shielding.

Unlocking graphene’s potential

Graphene’s inherent electrical transmitting properties make it ideal for 3D printing electronic devices, and a number of researchers have investigated its potential in this area.

Scientists from theUniversity of Nottinghammade a breakthrough in additive manufactured electronics in November 2020, when they fabricated graphene into multiple layers. The novel process yielded materials that could be used as a basis forfabricating enhanced additive semiconductors.

U.S. researchers on the other hand, have opted to utilizeOptomec’sAerosol Jet Printing(AJP) technology to fabricateelectrosensing food testing sensors. Using a graphene-based ink, the team were able to 3D print interdigitated electrodes onto a polymer base, forming devices that could be used in food processing facilities.

Elsewhere, a team based at theUniversity of Southern California(USC) have utilized the strength of graphene to 3D print a set ofnovel self-sensing armor. Although the scientists have only conducted tests with a LEGO figurine so far, they believe that in future, it could be deployed within military applications.

The researchers’ findings are detailed in their paper titled “Printability and performance of 3D conductive graphite structures.” The research was co-authored by Roneisha Haney, Phong Tran, Edward B.Trigg, Hilmar Koerner, Tarik Dickens and Subramanian Ramakrishnan.

To stay up to date with the latest 3D printing news, don’t forget to subscribe to the3D Printing Industry newsletteror follow us onTwitteror liking our page onFacebook.

Are you looking for a job in the additive manufacturing industry? Visit3D Printing Jobsfor a selection of roles in the industry.

Featured image shows a 3D printed cone of graphene-based material that the FAMU-FSU team used for masks in their lab. Photo via FAMU-FSU.